With its unique advantages and adaptability, solar LED traffic light has been widely used all over the world. So how to install solar LED traffic light correctly? What are the common installation mistakes? LED traffic light manufacturer Qixiang will show you how to install it correctly and how to avoid mistakes.
How to install solar LED traffic light
1. Solar panel installation: Put the solar panel on the panel bracket and tighten the screws to make it firm and reliable. Connect the output wire of the solar panel, pay attention to connect the positive and negative electrodes of the solar panel correctly, and tie the output wire of the solar panel firmly with a cable tie. After connecting the wires, tin-plate the wiring of the battery board to prevent the wires from oxidizing.
LED lamp installation: Pass the lamp wire out of the lamp arm, and leave a section of lamp wire at the end where the lamp head is installed to facilitate the installation of the lamp head. Support the light pole, pass the other end of the light wire through the thread hole reserved on the light pole, and run the light line to the top end of the light pole. And install the lamp head on the other end of the lamp wire. Align the lamp arm with the screw hole on the lamp pole, and then use a quick wrench to tighten the lamp arm with screws. Fasten the lamp arm after visually checking that the lamp arm is not skewed. Mark the end of the light wire passing through the top of the light pole, and make it compatible with the solar panel
Thread the two wires together to the bottom end of the light pole with a thin threading tube, and fix the solar panel on the light pole.
2. Lifting the light pole: put the sling on the appropriate position of the light pole, and slowly lift the lamp. Avoid scratching the solar panels by the steel wire rope of the crane. When the light pole is hoisted to the foundation, slowly lower the light pole, rotate the light pole at the same time, adjust the lamp holder to the road surface, and align the holes on the flange with the anchor bolts. The flange plate falls on the dirt on the foundation, put on the flat pad, spring pad and nut in turn, and finally tighten the nut evenly with a wrench to fix the light pole. Remove the lifting rope, and check whether the light pole is tilted, and adjust the light pole if not.
3. Battery and controller installation: put the battery into the battery well, and use a thin iron wire to pass the battery line to the roadbed. Connect the connection wires to the controller according to the technical requirements; first connect the battery, then the load, and then the solar panel; when wiring, be sure to pay attention to the wiring terminals marked on the controller.
Installation misunderstanding of solar LED traffic light
1. Extend the connection line of the solar panel at will
In some places, because there is too much interference from the installation of solar panels, the panels and lights will be separated for a long distance, and then they will be connected with two-core wires bought in the market at will. Because the quality of the general wires on the market is not very good, and the distance between the wires is very long and the wire loss is large, the charging efficiency will be greatly reduced, which will affect the lighting time of the solar traffic lights.
2. The angle of the solar panel is not allowed
The accurate angle adjustment of the solar panel needs to follow the simple principle. For example, let the sunlight directly shine on the solar panel, then its charging efficiency is the largest; in different places, the tilt angle of the solar panel can refer to the local latitude, and adjust the solar traffic light solar energy according to the latitude. The tilt angle of the board.
3. The direction of the solar panel is wrong
For the sake of aesthetics, the installer may install the solar traffic signal light solar panels face to face in a tilted and symmetrical manner, but if one side is oriented correctly, the other side must be wrong, so the wrong side will not be able to directly reach the solar panels because of the light. Its charging efficiency will decrease.
4. There are too many obstacles in the installation position
Leaves, buildings, etc. block the light, affecting the absorption and utilization of light energy, which leads to low charging efficiency of solar panels.
5. Workers make mistakes
The on-site staff will not use the engineering remote control correctly, resulting in the wrong parameter setting of the solar traffic signal light, so the light will not turn on.
The above are the correct installation steps of solar LED traffic light and common installation misunderstandings. LED traffic light manufacturer Qixiang hopes to help everyone, so that not only can the product be better promoted, but also energy can be saved.
If you are interested in solar LED traffic light, welcome to contact LED traffic light manufacturer Qixiang to read more.
Post time: Apr-07-2023
